úé÷åï øòéãåú àöì îåøé, îé éåãò ?

[idosit]

îçôù äúééçñåú ùì çáø'ä òí ôæ"í ùì ùðä / ùðúééí ìàçø äúé÷åï.
ëîä òìä / äàí îçæé÷ îòîã / äàí éù îùîòåéåú ðåñôåú.
úåãä

[haimzis]

ñéãøúé àöìå ìôðé ùðä åçöé, åäëì áñãø âîåø ääâä ìà øåòã.

[idosit]

çééí úåãä. áàéæä ñëåí îãåáø. äàí éù îùîòåéåú ðåñôåú [ øëåú äâä, ùøéãåú îëìåìéí àçøéí, âåáä .....] ?

[haimzis]

áðåâò ìñëåí àðé ìà øåöä ìäâéã ñúí ãáø àéúå.
äøëá îúðäâ ëîå ùøëá àîåø ìäúðäâ, àéï øòéãåú àéï äøâùä ùì çåôù, ðúï ôúøåï ìáòéä, îîìéõ áçåí.

[gmike]

äôúøåï ùîåøé îöéò äåà ìôé äåøàú äùéøåú äøùîéú ùì ñåæå÷é ìáòéä. àí îòðééï àåúê éù òì æä îéãò áøùú.

[idor]

áäðçä ååéãàú ùàéï ìê áòéåú àçøåú (âìâìéí ìà îàåæðéí, îåè äéðò ò÷åí, áåùéðâéí, ÷éðâôéðéí)
æä ìà äøáä òáåãä åìà ãåøù ëìéí îéåçãéí (áãéòáã ìà äéä öåøê áçåìõ úôåçéí ù÷ðéúé ëé äí äùúçøøå áìé áòéåú)
òìåú äùéîñéí æðéçä.
http://www.bigjimny.com/store/index....t&product_id=8
îðñéåï àöìé 0.7 îî áëì ÷éðâôéï. äáòéä ðôúøä åääâä éöéá åðòéí.

[gmike]

àôùø ëîåáï ì÷ðåú àú äùéîñéí âí áîëùéøé úðåòä áàøõ..

[idosit]

úåãä òì ëì äàéðôåøîöéä òã ëàï.
àðé ëáø ë ùðúééí àçøé ùéîñéí åäúåôòä îúçéìä ìçæåø.
ìôé îåñê ñåæå÷é, ùéîñéí ðéúï ìäåñéó ø÷ ôòí àçú.
ëê ùòëùéå ðãøù ôúøåï ùåðä åîùîòåúé éåúø.

[gmike]

äùéîñéí ðåòãå ìúú ìçõ ðåñó òì îéñáé ä÷éðâ ôéï, ùäí ÷åðééí. òí äæîï äí îúáìéí, åðåöø ùåá çåôù. æä ëðøàä äîöá àöìê.
úáãå÷ ú÷éðåú îéñáéí, àí ú÷éðéí-àôùø ìäçìéó ùéîñéí ìéåúø òáéí, àå îéñáéí çãùéí åìäúàéí ùéîñéí îçãù..

[eladss]

ääåøàåú ùì ñåæå÷é îöåøôåú

[idor]

àåôöéä ðåñôú. àðé òáãúé ìôé äùéèä ùëúåáä á bigjimny îàçø åìà äéúä ìé àôùøåú ìîãåã îù÷ì îùéëä - æä äéä ÷ì ìééùåí.

Undo each Kingpin and slip on a shim. Do both the top and bottom at the same time and then tighten the kingpins back up. Try moving the hub from left to right. If you are doing the "Suzuki" method you should pull the hub with a spring balance and measure the starting "pull". This is really difficult so I did it by hand. Add and remove shims until the wheel moves smoothly but firmly (not too loose) from side to side. Sometimes it feels "lumpy", this is not desirable and add or remove more shims to remove it - strangely adding more shim thickness can remove it. Do not get it to the point where the hub will not swivel. Take your time and get it to a point where you are happy that it is firm but not at the point where you will wear out the bearing in 5 minutes.

[idosit]

îéùäå ùîò îùäå òì äçìôú äâ'ðèéí îîâðæéåí ì ôç ?

[ùâéà S]

ëï. æä ìà îä ùòåæø.